Seite 1
SGH10 Seilzuggeber Deutsch Originalmontageanleitung Seite 2 Wire-Actuated Encoder English Translation of the Original Installation Instructions page 14 220/17...
Todesfolge, Sachschäden oder ungeplanten Gerätereaktionen führen können, sofern Sie die gegebenen Anweisungen missachten. Gefährdungen, die zu schweren Körperverletzungen, Sachschäden oder WARNUNG ungeplanten Gerätereaktionen führen können, sofern Sie die gegebenen Anweisungen missachten. SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
Automatisierungstechnik vertraut sind; • als Inbetriebnahme- und Monatagepersonal berechtigt sind, Strom- kreise und Geräte/Systeme gemäß den Standards der Sicherheitstech- nik in Betrieb zu nehmen, zu erden und zu kennzeichnen. SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
Abb. 1: Federgehäuse 3 Identifikation Das Typenschild zeigt die Seriennummer mit dem Gerätetyp. Die Lieferpa- piere ordnen jeder Seriennummer eine detaillierte Bestellbezeichnung zu. z. B. 0000000-SGH10 Geräte-Typ Seriennummern SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
ACHTUNG Die Spannungswerte sind abhängig von der Geräteausführung und sind den technischen Daten in Kapitel zu entnehmen. +UB +UB +UB Lim1 Lim2 Abb. 4: Anschluss Strom- und Spannungsausgang SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
Hitze und Feuchtigkeit schützen. • Anschlüsse weder durch mechanische noch durch thermische Einflüsse beschädigen. • Vor Montage ist der Seilzuggeber auf Transportschäden zu untersu- chen. Beschädigte Seilzuggeber nicht einbauen. SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
Das ProTool SGH ist eine Programmierhilfe für das SGH10. • Zubehör SIKO Art. Nr. "ProTool SGH" 9 Technische Daten Mechanische Daten Ergänzung Flansch Aluminium Dichtring (PUR) Gehäuse Kunststoff Seiltyp ø0.45 mm Stahlseil (rostfrei) SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
Seite 12
1000 mm Messlänge ±0.5 % 500 mm Messlänge Schnittstelle gemäß ISO 11898, CANopen, CIA 406, CIA 301 nicht getrennt Adresse einstellbar per SDO oder Layer Setting Ser- vice (LSS) SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
Seite 13
Zylinder (IP69K) verbaut mit KV1H und geeignetem Gegenste- cker Schockfestigkeit 1000 m/s , 11 ms EN 60068-2-27 Vibrationsfestigkeit 70 m/s , 10 Hz ... 2 kHz EN 60068-2-64 SGH10 · Datum 14.07.2017 · Art. Nr. 88312 · Änd. Stand 220/17...
Seite 14
5 Adjustment and alignment (voltage/current) 6 Commissioning 7 Transport, Storage, Maintenance and Disposal 8 Accessory 8.1 Cable extension KV1H 8.2 Installation tool ZB4004 8.3 ProTool SGH 9 Technical data SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
Danger that may cause minor injury, property damage or unplanned device CAUTION reactions if you disregard the instructions given. SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
• are familiar with the safety guidelines of the electrical and automation technologies when performing configuration tasks; • are authorized to commission, earth and label circuits and devices/ systems in accordance with the safety standards. SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
Please check the particular type of unit and type number from the identifi- cation plate. Type number and the corresponding version are indicated in the delivery documentation. e. g. 0000000 SGH10 type of unit version number SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
Destruction of the wire-actuated encoder WARNING If welding is performed too near to the cylinder with the SGH10 installed, the whole weld current can flow over the SGH10 in case of inadequate grounding resulting in possible damage to the measuring rope or elec- tronic system of the SGH10.
Seite 19
3. Tighten the threaded pin slightly (approx. 0.5Nm) and then turn back again approx. 0.5 turns. Under operating pressure, no radial force may be applied to the SGH10 NOTICE while securing, as otherwise the compressive strength might be influ- enced.
The voltage values are a function of the device design and can be referred to in the technical data in chapter 9. +UB +UB +UB Lim1 Lim2 Fig. 4: Connection voltage- and current output SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
Fig. 5: signal sequence voltage output (e.g. 0-10 V) Lim1 Lim2 20 mA 20 mA 4 mA length 4 mA Lim1 Lim2 length length Lim1 Lim2 Fig. 6: signal sequence current output (e.g. 4-20 mA) SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
This will ensure correct instal- lation and the operating reliability of the device. The startup operation of SGH10 in the cylinder should be carried out with hydraulic oil. If the startup is performed with compressed air, the moving parts must be lubri- cated beforehand.
• Accessory SIKO art. no. "ProTool SGH" 9 Technical data Mechanical data Additional information Flange aluminum sealing ring (PUR) Housing synthetic Wire design ø0.45 mm Steel rope (stainless) Extension force ≥2 N SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
Seite 24
1000 mm ±0.5 % 500 mm Interface according to ISO 1189, CANopen, CIA 406, CIA 301 not isolated Address adjustable per SDO or Layer Setting Ser- vice (LSS) SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...
Seite 25
(IP69K), with KV1H and suitable mating connector Shock resistance 1000 m/s , 11 ms EN 60068-2-27 Vibration resistance 70 m/s , 10 Hz … 2 kHz EN 60068-2-64 SGH10 · Date 14.07.2017 · Art. No. 88312 · Mod. status 220/17...