Inhaltsverzeichnis
Verfügbare Sprachen
Verfügbare Sprachen
SYSTEM SPECIFICATIONS
Lower cut-off frequency, –3 dB:
_____________________________________________
Upper cut-off frequency, –3 dB:
_____________________________________________
Free field frequency response of system:
_____________________________________________
Maximum short term sine wave acoustic output on axis in
half space, averaged from 100 Hz to 3 kHz:
_____________________________________________
Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by driver unit
protection circuit):
_____________________________________________
Maximum peak acoustic output per pair on top of
console, @ 1 m distance with music material: > 108 dB
_____________________________________________
Self generated noise level in free field @ 1 m on axis:
_____________________________________________
Harmonic distortion at 85 dB SPL @ 1 m on axis:
Freq:
_____________________________________________
Drivers: Bass
Treble
Both drivers are magnetically shielded
_____________________________________________
Weight:
_____________________________________________
Dimensions: Height
(including Iso-Pod™ table stand)
Height
(without Iso-Pod™ table stand)
Width
Depth
EC DECLARATION OF CONFORMITY
This is to certify that the Genelec Monitoring System
8030A conforms to the following standards:
Safety:
EN 60065: 2002 + A1:2006 + A11:2009/
IEC 60065:2001 7th Edition + A1: 2005
EMC:
EN 55020 A2: 2008
EN 55013: (2001)+ A1 : 2003 + A2: 2009
EN 61000-3-2: 2006
EN 61000-3-3 A2: 2005
The product herewith complies with the requirements of
The Low Voltage Directive 2006/95/EC and EMC Directive
2004/108/EC
Signed:
Ilpo Martikainen
Position:
Chairman of the Board
Date:
12-January-2009
< 55 Hz
> 21 kHz
58 Hz – 20 kHz (± 2.0 dB)
@ 1 m > 100 dB SPL
@ 0.5 m > 106 dB SPL
@ 1 m > 97 dB SPL
< 10 dB (A-weighted)
50...100 Hz < 2 %
>100 Hz < 0.5 %
130 mm (5") cone
19 mm (
/
") metal dome
3
4
5.6 kg (12.3 lb)
299 mm (11
/
")
13
16
285 mm (11
/
")
1
4
189 mm (7
7
/
")
16
178 mm (7")
CROSSOVER SECTION
Connectors:
Input: XLR female, balanced 10 kOhm,
Output: XLR male, balanced 100 Ohm,
_____________________________________________
Input level for 100 dB SPL output at 1 m:
-6 dBu at volume control max
_____________________________________________
Volume control range:
-80 dB relative to max output
Output signal level is 0 dB relative to input signal level
but adjustable by volume control
_____________________________________________
Crossover frequency, Bass/Treble:
_____________________________________________
Treble Tilt control operating range:
_____________________________________________
Bass Roll-Off control operating in a –6 dB step @ 85 Hz
(to be used in conjunction with a 7050B subwoofer)
_____________________________________________
Bass Tilt control operating range in –2 dB steps:
_____________________________________________
The 'CAL' position is with all tone controls set to 'off' and
the input sensitivity control to maximum (fully clockwise).
AMPLIFIER SECTION
Bass amplifier output power with an 8 Ohm load: 40 W
Treble amplifier output power with an 8 Ohm load: 40 W
Long term output power is limited by driver unit protection
circuitry.
_____________________________________________
Amplifier system distortion at nominal output:
THD
SMPTE-IM
CCIF-IM
DIM 100
_____________________________________________
Signal to Noise ratio, referred to full output:
Bass
Treble
_____________________________________________
Mains voltage:
Voltage operating range:
Power consumption:
Idle
Full output
pin 1 gnd, pin 2 +, pin 3 -
pin 1 gnd, pin 2 +, pin 3 -
3.0 kHz
0 to –2 dB @ 15 kHz
0 to –6 dB @ 100 Hz
< 0.05 %
< 0.05 %
< 0.05 %
< 0.05 %
> 100 dB
> 100 dB
100, 120, 220 or 230 V
according to region
±10 %
10 VA
80 VA
English 7
Inhaltsverzeichnis
