Seite 1
EDK82ZAFSC .5r÷ Montageanleitung Mounting Instructions Instructions de montage STANDARD−I/O E82ZAFSC Funktionsmodul Function module Module de fonction...
Seite 2
Lesen Sie zuerst diese Anleitung und die Dokumentation zum Grundgerät, bevor Sie mit den Arbeiten beginnen! Beachten Sie die enthaltenen Sicherheitshinweise. Please read these instructions and the documentation of the standard device before you start working! Observe the safety instructions given therein! Lire le présent fascicule et la documentation relative à...
Seite 4
Schalter zur Konfigurierung des analogen Frequenzsollwertes an Klemme X3/8 ^ 14 Digitale und analoge Ein− und Ausgänge, Klemmenleiste X3 Typenschild 0Abb. 0Tab. 0 Tipp! Aktuelle Dokumentationen und Software−Updates zu Lenze Produkten finden Sie im Internet jeweils im Bereich "Services & Downloads" unter http://www.Lenze.com EDK82ZAFSC DE/EN/FR 4.0...
Sicherheitshinweise Definition der verwendeten Hinweise Sicherheitshinweise Definition der verwendeten Hinweise Um auf Gefahren und wichtige Informationen hinzuweisen, werden in dieser Dokumenta- tion folgende Piktogramme und Signalwörter verwendet: Sicherheitshinweise Aufbau der Sicherheitshinweise: Gefahr! (kennzeichnet die Art und die Schwere der Gefahr) Hinweistext (beschreibt die Gefahr und gibt Hinweise, wie sie vermieden werden kann) Piktogramm und Signalwort...
Sicherheitshinweise Restgefahren Restgefahren Gefahr! Beachten Sie die in den Anleitungen zum Grundgerät enthaltenen Sicherheitshinweise und Restgefahren. EDK82ZAFSC DE/EN/FR 4.0...
Mechanische Installation Mechanische Installation Folgen Sie zur mechanischen Installation des Funktionsmoduls den Hinweisen in der Mon- tageanleitung des Grundgerätes. Die Montageanleitung des Grundgerätes ƒ ist Teil des Lieferumfangs und liegt jedem Gerät bei. ƒ gibt Hinweise, um Beschädigungen durch unsachgemäße Behandlung zu vermeiden. ƒ...
Elektrische Installation EMV−gerechte Verdrahtung Elektrische Installation EMV−gerechte Verdrahtung Für eine EMV−gerechte Verdrahtung beachten Sie folgende Punkte: Hinweis! Steuerleitungen getrennt von Motorleitungen verlegen. ƒ Schirme so weit wie möglich an die Klemmen führen (ungeschirmte ƒ Aderlänge < 40 mm). Legen Sie die Schirme der Steuerleitungen bzw. Datenleitungen wie folgt ƒ...
Elektrische Installation Verdrahtung Verdrahtung Daten der Anschlussklemmen Elektrischer Anschluss Klemmleiste mit Schraubanschluss Anschlussmöglichkeiten starr: 1,5 mm (AWG 16) flexibel: ohne Aderendhülse 1,0 mm (AWG 18) mit Aderendhülse, ohne Kunststoffhülse 0,5 mm (AWG 20) mit Aderendhülse, mit Kunststoffhülse 0,5 mm (AWG 20) Anzugsmoment 0,22 ...
Seite 13
Elektrische Installation Verdrahtung Versorgung über die interne Spannungsquelle (X3/20): X3/28, Reglersperre (CINH) X3/E1 ..X3/E4, digitale Eingänge GND2 GND1 GND1 +20V 20 28 E1 E2 E3 E4 39 A1 59 AOUT1 AIN1 DIGOUT1 1k … 10k E82ZAFS004 Versorgung über eine externe Spannungsquelle: X3/28, Reglersperre (CINH) X3/E1 ...
Seite 14
Ausgangspegel 0 +10 V: Offset (C0109/C0422) und Verstärkung (C0108/C0420) anpassen Offset (C0026) und Verstärkung (C0027) für jedes Funktionsmodul separat abgleichen: Nach Austausch des Funktionsmoduls oder des Grundgerätes Nach Laden der Lenze−Einstellung Wahlweise Frequenzeingang 0 10 kHz einspurig oder 0 ... 1 kHz zweispurig, Konfiguration über C0425...
Inbetriebnahme Vor dem ersten Einschalten Inbetriebnahme Vor dem ersten Einschalten Hinweis! Wenn Sie die Inbetriebnahme mit einer von der Lenze−Einstellung ƒ abweichenden Konfiguration durchführen, lesen Sie die Anweisungen "Individuelle Einstellungen" ^ 17. Achten Sie darauf, ƒ – dass Sie mit dem DIP−Schalter am Funktionsmodul den Sollwertbereich richtig eingestellt haben, siehe ^ 16.
DIP−Schalter auf Spannungsbereich 0 ... 5 V einstellen. Andernfalls kann nicht der ganze Drehzahlbereich durchfahren werden. Signal an X3/8 C0034 Schalterstellung 0 ... 5 V 0 ... 10 V (Lenze−Einstellung) 0 ... 20 mA 4 ... 20 mA 4 ... 20 mA drahtbruchüberwacht −10 V ... +10 V...
Inbetriebnahme Mit Lenze−Einstellung Mit Lenze−Einstellung Schritt Vorgehensweise Bemerkungen Netzspannung zuschalten. Das Grundgerät ist nach ca. 1 Sekunde betriebsbereit. Die Reglersperre ist aktiv. Reaktion des Grundgerätes Die grüne LED blinkt. Keypad: (falls aufgesteckt) Digitale Eingänge ansteu- Lenze−Einstellung ern. Rechtslauf: – E1, E2, E3, E4: LOW Linkslauf: –...
Seite 18
Inbetriebnahme Mit Lenze−Einstellung Hinweis! Das Grundgerät ist nur funktionsfähig, wenn HIGH−Pegel an X3/28 anliegt ƒ (Reglerfreigabe über Klemme). – Beachten Sie, dass die Reglersperre über mehrere Quellen gesetzt werden kann. Die Quellen wirken wie eine Reihenschaltung von Schaltern. – Wenn der Antrieb trotz Reglerfreigabe über X3/28 nicht anläuft, überprüfen Sie, ob noch über eine andere Quelle Reglersperre gesetzt...
Technische Daten Abmessungen Abmessungen E82ZAFS002A alle Maße in mm EDK82ZAFSC DE/EN/FR 4.0...
Seite 22
Digital and analog inputs and outputs, terminal strip X3 ^ 23 Nameplate 0Fig. 0Tab. 0 Tip! Current documentation and software updates concerning Lenze products can be found on the Internet in the "Services & Downloads" area under http://www.Lenze.com EDK82ZAFSC DE/EN/FR 4.0...
Seite 23
Hardware version Order designation E82ZAFSC00x Function The function module enables the user to control Lenze frequency inverters and Drive PLCs with analog and digital control signals. Application range Can be used together with: Can be used as of standard device version...
Seite 24
............Commissioning using Lenze settings .
Safety instructions Definition of notes used Safety instructions Definition of notes used The following pictographs and signal words are used in this documentation to indicate dangers and important information: Safety instructions Structure of safety instructions: Danger! (characterises the type and severity of danger) Note (describes the danger and gives information about how to prevent dangerous situations)
Safety instructions Residual hazards Residual hazards Danger! Observe the safety instructions and residual hazards included in the instructions for the standard device. EDK82ZAFSC DE/EN/FR 4.0...
Mechanical installation Mechanical installation Follow the notes given in the Mounting Instructions for the standard device for the mechanical installation of the function module. The Mounting Instructions for the standard device ƒ are part of the scope of supply and are enclosed with each device. ƒ...
Electrical installation Wiring according to EMC Electrical installation Wiring according to EMC Please observe the following for wiring according to EMC guidelines: Note! Separate control cables from motor cables. ƒ Lead the shields as far as possible to the terminals (unshielded core length ƒ...
Electrical installation Wiring Wiring Terminal data Electrical connection Terminal strip with screw connection Possible connections rigid: 1.5 mm (AWG 16) flexible: without wire end ferrule 1.0 mm (AWG 18) with wire end ferrule, without plastic sleeve 0.5 mm (AWG 20) with wire end ferrule, with plastic sleeve 0.5 mm (AWG 20)
Seite 31
Electrical installation Wiring Supply via the internal voltage source (X3/20): X3/28, controller inhibit (CINH) X3/E1 ..X3/E4, digital inputs GND2 GND1 GND1 +20V 20 28 E1 E2 E3 E4 39 A1 59 AOUT1 AIN1 DIGOUT1 1k … 10k E82ZAFS004 Supply via an external voltage source: X3/28, controller inhibit (CINH) X3/E1 ...
Seite 32
Adjust offset (C0026) and gain (C0027) separately for each function module: After replacing the function module or the standard device After loading the Lenze setting Alternatively frequency input 0 10 kHz single−tracked or 0 ... 1 kHz double−tracked, configuration via C0425 EDK82ZAFSC DE/EN/FR 4.0...
Commissioning Before switching on Commissioning Before switching on Note! If your configuration differs from the Lenze settings, please read the ƒ ^ 35 instructions given under "Individual settings" Please check ƒ – that the setpoint range is set correctly for the function module using...
0 ... 5 V. Otherwise it is not possible to use the whole speed range. Signal at X3/8 C0034 Switch position 0 ... 5 V 0 ... 10 V (Lenze setting) 0 ... 20 mA 4 ... 20 mA 4 ... 20 mA Open−circuit monitoring −10 V ...
Commissioning Commissioning using Lenze settings Commissioning using Lenze settings Step Procedure Remarks Switch on the mains The controller is ready for operation after approx. 1 second. voltage. Controller inhibit is active. Drive response: The green LED is blinking. Keypad: (if attached) Control digital inputs.
Seite 36
Commissioning Commissioning using Lenze settings Note! The controller is only ready for operation if a HIGH signal is applied to ƒ X3/28 (controller enable via terminal). – Please observe that the controller can be inhibited through various sources. All sources act like a series connection of switches.
Technical data Connection data Technical data Connection data Resolution: 10 bit Linearity error: ±0.5 % Temperature error: 0.3 % (0 +60 °C) Carrying capacity I = 2 mA Resolution: 10 bit Linearity error: ±0.5 % Temperature error: 0.3 % (0 +60 °C) Input resistance >...
Technical data Dimensions Dimensions E82ZAFS002A All dimensions in mm EDK82ZAFSC DE/EN/FR 4.0...
Seite 40
Entrées et sorties numériques et analogiques, bornier X3 ^ 41 Plaque signalétique 0Fig. 0Tab. 0 Conseil ! Les mises à jour de logiciels et les documentations récentes relatives aux produits Lenze sont disponibles dans la zone "Téléchargements" du site Internet : http://www.Lenze.com EDK82ZAFSC DE/EN/FR 4.0...
Seite 41
Validité Le présent document s’applique aux modules suivants : ƒ Modules de fonction E82ZAFSC (E/S standard) à partir de la version 3A : Ce document est uniquement valable avec la documentation relative aux appareils de base compatibles. Identification ...
Consignes de sécurité Définition des conventions utilisées Consignes de sécurité Définition des conventions utilisées Pour indiquer des risques et des informations importantes, la présente documentation utilise les mots et symboles suivants : Consignes de sécurité Présentation des consignes de sécurité Danger ! (Le pictogramme indique le type de risque.) Explication...
Consignes de sécurité Dangers résiduels Dangers résiduels Danger ! Tenir compte des consignes de sécurité et des dangers résiduels décrits dans la documentation de l’appareil de base concerné. EDK82ZAFSC DE/EN/FR 4.0...
Installation mécanique Installation mécanique Pour l’installation mécanique du module de fonction, suivre les consignes fournies dans les instructions de montage de l’appareil de base. Les instructions de montage de l’appareil de base ƒ font partie de la livraison standard et sont comprises dans l’emballage, ƒ...
Installation électrique Câblage conforme CEM Installation électrique Câblage conforme CEM Pour réaliser un câblage conforme CEM, respectez les points suivants : Remarque importante ! Poser les câbles de commande séparément des câbles moteur. ƒ Conduire le blindage aussi loin que possible vers les bornes (longueur de fil ƒ...
Installation électrique Câblage Câblage Spécifications des bornes de raccordement Raccordement électrique Bornier à vis Raccordements possibles Rigide : 1,5 mm (AWG 16) Souple : sans embout 1,0 mm (AWG 18) avec embout, sans cosse en plastique 0,5 mm (AWG 20) avec embout et cosse en plastique 0,5 mm (AWG 20)
Seite 50
Installation électrique Câblage Type de signal Fonction Niveau (réglage Lenze : en caractères gras) Sortie Fréquence de sortie 0 +6 V analogique 0 +10 V − GND1, potentiel de référence pour les signaux − analogiques Entrée Entrée pour valeur réelle ou consigne analogique Commuter la plage à...
Avant la première mise sous tension Mise en service Avant la première mise sous tension Remarque importante ! Pour la mise en service d’une configuration qui diffère du réglage Lenze, ƒ ^ 53 lire les instructions fournies au paragraphe "Réglages individuels"...
0 ... 5 V. Autrement, il ne sera pas possible de parcourir la plage de vitesse dans son intégralité. Signal au niveau de X3/8 C0034 Position de l’interrupteur 0 ... 5 V 0 ... 10 V (réglage Lenze) 0 ... 20 mA 4 ... 20 mA 4 ... 20 mA avec protection contre rupture de fil −10 V ...
Mise en service Avec réglage Lenze Avec réglage Lenze Etape Action Remarques Activer la tension réseau L’appareil de base est opérationnel après env. 1 seconde. Le blocage variateur est activé. Réaction de l’appareil de base La LED verte clignote. Clavier de commande : (s’il est raccordé)
Seite 54
Mise en service Avec réglage Lenze Remarque importante ! L’appareil de base n’est opérationnel que lorsque le niveau HAUT est requis ƒ au niveau de la borne X3/28 (déblocage du variateur par la borne). – Veiller à ce que le blocage variateur puisse être défini au moyen de plusieurs sources.