Maintenance - Makita BO6030 Betriebsanleitung
Exzenterschleifer
Vorschau ausblenden
Andere Handbücher für BO6030:
- Betriebsanleitung (41 Seiten) ,
- Bedienungsanleitung (37 Seiten) ,
- Betriebsanleitung (33 Seiten)
Inhaltsverzeichnis
Verfügbare Sprachen
Verfügbare Sprachen
Switch action (Fig. 12)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop. For continuous operation, pull the trigger and
then push in the lock button. To stop the tool from the
locked position, pull the trigger fully, then release it.
Speed adjusting dial (Fig. 12)
The tool speed can be infinitely adjusted between
4,000 opm and 10,000 opm by turning the speed adjust-
ing dial, which is marked 1 to 5. Higher speed is obtained
when the dial is turned in the direction of number 5; lower
speed is obtained when it is turned in the direction of
number 1. Refer to the figure below for the relationship
between the number setting on the adjusting dial and the
kind of work.
A range
A range: For polishing
B range: For finish sanding
C range: For regular sanding
NOTE:
The above figure shows standard applications. They may
differ under certain conditions.
Sanding operation (Fig. 13)
CAUTION:
• Never switch on the tool when it is in contact with the
workpiece surface, causing an injury to operator.
• Never run the tool without the abrasive disc. You may
seriously damage the pad.
• Never force the tool. Excessive pressure may decrease
the sanding efficiency, damage the abrasive disc or
shorten tool life.
Turn the tool on and wait until it attains full speed. Then
gently place the tool on the workpiece surface. Keep the
base flush with the workpiece and apply slight pressure
on the tool.
Polishing operation
CAUTION:
• Use only a Makita genuine sponge pad, felt pad or wool
pad (optional accessories).
• Always operate the tool at low speed to prevent work
surfaces from damage/burning.
C range
B range
Dial setting
• Never force the tool. Excessive pressure may decrease
the polishing efficiency and cause motor overload,
resulting in tool malfunction.
1.
Applying wax (Fig. 14)
Use an optional sponge pad. Apply wax to the
sponge pad or work surface. Run the tool to smooth
out wax.
NOTE:
First, wax a non critical portion of the work surface to
make sure that the tool will not scratch the surface or
result in uneven waxing.
2.
Removing wax (Fig. 15)
Use an optional felt pad. Run the tool to remove
wax.
3.
Polishing (Fig. 16)
Use an optional wool pad. Run the tool and apply
the wool pad gently to the work surface.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by a Makita
Authorized Service Center.
ACCESSORIES
CAUTION:
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Hook-and-loop system abrasive disc
(with pre-punched holes)
Grit
40
60
Use
Coarse
• Hook-and-loop system sponge pad
• Hook-and-loop system felt pad
• Hook-and-loop system wool pad
• Pad 150 (Super soft, Soft)
• Sanding cloth 150 – #100, #200, #800 for fine sanding
• Hex wrench 5
• Paper dust bag
• Paper dust bag holder
80
120
180
240
Medium
Fine
400
7
Inhaltsverzeichnis
