Inhaltsverzeichnis
Verfügbare Sprachen
Verfügbare Sprachen
GENERAL
Carefully read the following important information regarding
installation safety and maintenance. Keep this information
booklet accessible for further consultations. The appliance has
been designed for use in the ducting version (air exhaust to
the outside – Fig.1B), fi ltering version (air circulation on the
inside – Fig.1A) or with external motor (Fig.1C).
SAFETY PRECAUTION
1. Take care when the cooker hood is operating simultaneously
with an open fi replace or burner that depend on the air in the
environment and are supplied by other than electrical energy,
as the cooker hood removes the air from the environment
which a burner or fi replace need for combustion. The negative
pressure in the environment must not exceed 4Pa (4x10-5 bar).
Provide adequate ventilation in the environment for a safe
operation of the cooker hood. Follow the local laws applicable
for external air evacuation.
Before connecting the model to the electricity network:
- Control the data plate (positioned inside the appliance)
to ascertain that the voltage and power correspond to the
network and the socket is suitable. If in doubt ask a qualifi ed
electrician.
2. Warning !
In certain circumstances electrical appliances may be a
danger hazard.
A) Do not check the status of the fi lters while the cooker
hood is operating
B) Do not touch bulbs or adjacent areas, during or straight
after prolonged use of the lighting installation.
C) Disconnec t the elec trical plug prior to any
maintenance.
D) This appliance is not intended for use by young children
or infi rm persons without supervision
E) Young children should be supervised to ensure they do
not play with the appliance
F) There shall be adequate ventilation of the room when
the rangehood is used at the same time as appliances
burning gas or other fuels
G) There is a risk of fi re if cleaning is not carried out in
accordance with the instructions
This appliance conforms to the European Directive, Waste
Electrical and Electronic Equipment (WEEE). By making sure
that this appliance is disposed of in a suitable manner, the user
is helping to prevent potential damage to the environment
or to public health.
The
symbol on the product or on the accompanying
paperwork indicates that the appliance should not be treated
as domestic waste, but should be delivered to a suitable
electric and electronic appliance recycling collection point.
Follow local guidelines when disposing of waste. For more
information on the treatment, re-use and recycling of this
product, please contact your local authority, domestic waste
collection service or the shop where the appliance was
purchased.
ENGLISH
INSTALLATION INSTRUCTIONS
Assembly and electrical connections must be carried out
by specialised personnel.
• Electric Connection
The appliance has been manufactured as a class II, therefore
no earth cable is necessary.
The plug must be easily accessible after the installation of
the appliance.
• If the hob is electric, gas, or induction, the minimum distance
between the same and the lower part of the hood must be
at least 65 cm.
If a connection tube composed of two parts is used, the
upper part must be placed outside the lower part. Do not
connect the cooker hood exhaust to the same conductor
used to circulate hot air or for evacuating fumes from other
appliances generated by other than an electrical source.
Before proceeding with the assembly operations, remove
the anti-grease fi lter(s) (Fig.2) so that the unit is easier to
handle.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which has
the same diameter as the air exhaust outlet hole. If a pipe
with a smaller diameter is used, the effi ciency of the product
may be reduced and its operation may become noisier.
• Installation
The following instruction should be followed to carry out the
correct installation of the cooker hood.
1. Mounting of the cooker hood on the lower side of the
cupboard.
2. Selection of the version (extraction or fi ltration)
3. Before starting to fi x the hood, disconnect the anti-grease
fi lter for easier appliance handling:
- Open panel B as shown in Fig.2.
- Pull handle C as shown in Fig.3.
• Fitting the cooker hood into the lower part of the wall
cabinet
For all measurements relating to the cooker hood, please
refer to Fig.4.
Before fi xing the cooker hood to the lower part of the cabinet,
the following steps should be performed:
1- Remove the 4 screws E fi xing the two cooker hood lamps H
(RHS and LHS) in place as indicated in Fig. 5A.
2- Remove the lamps H and disconnect the connectors W of
the halogen lamps to make installation easier, as indicated
in Fig. 5B.
3. Make sure the thickness of the cabinet falls within the range
of values listed in Fig. 5C.
Fit the cooker hood in the cabinet (Fig. 6) and make sure the
4 springs are fi xed in place well.
Fix the cooker hood to the cabinet securely by using a
screwdriver to tighten the screws M until the appliance is
fl ush with the cabinet (Fig. 6).
4. Connect the connectors W of the halogen lamps again and
reinstall the lamps H fi xing them with the 4 screws E that were
previously removed.
- 12 -
GB
Inhaltsverzeichnis
