Inhaltsverzeichnis
Verfügbare Sprachen
Verfügbare Sprachen
2. Fix it in place using 4 screws B which are suited to the type
of cabinet installed, as indicated in fi gure 4.
- Fixing the hood to the wall (Fig. 5B)
1. Using the drill template supplied, make 2 fi xing holes in
accordance with the measurements listed.
When carrying out the fi xing procedures, use only screws
and screw anchors which are suited to the type of wall (e.g.
reinforced concrete, plasterboard etc.). If the screws and
screw anchors are supplied with the appliance, make sure
that they are suited to the type of wall to which the hood
must be fi xed.
Adjust the position of the brackets M in accordance with
the cabinet depth, using the caged nut N as indicated in
fi gure 5A.
2. Fix the hood to the bracket using screw G as indicated
in fi gure 5B.
3. Fix the hood to the wall using the 2 screws R (Fig. 5C).
- Fitting the spacers
Depending on your appliance model, use the following
installation instructions:
1. spacer I (Fig. 6).
To fi ll in any space remaining between the hood and the wall,
simply position spacer I next to the wall and fi x it in place
with the 3 screws
L as indicated in fi gure 6.
2. spacer O (Fig. 7).
see note (*) Warning: plastic spacer fi tting
• Extractor version
When installed in this way the appliance expels fumes outside,
either through a perimeter wall or existing ducting. It is
therefore necessary to purchase a non-fl ammable air exhaust
tube which complies with all current legislation and connect
it to the fl ange F supplied (Fig. 8).
• Filter version
To transform an extractor hood version into a fi lter hood
version, contact your appliance dealer and ask for active
carbon fi lters.
The air is released back into the room through connection
piping which passes through the cabinet and is connected
to fl ange F (Fig. 9).
The active carbon fi lters must be fi tted inside the hood.
To replace the filters, pull lever H outwards as shown in
(Fig.3).
USE AND MAINTENANCE
• We recommend that the cooker hood is switched on before
any food is cooked.
We also recommend that the appliance is left running for
15 minutes after the food is cooked, in order to thoroughly
eliminate all contaminated air.
The eff ective performance of the cooker hood depends on
constant maintenance; the anti-grease fi lter and the active
carbon fi lter both require special attention.
• The anti-grease fi lter is used to trap any grease particles
suspended in the air, therefore is subject to saturation (the
time it takes for the fi lter to become saturated depends on
the way in which the appliance is used).
- To prevent potential fi re hazards, the anti-grease fi lters should
be washed a minimum of every 2 months (it is possible to use
the dishwasher for this task).
- After a few washes, the colour of the fi lters may change. This
does not mean they have to be replaced.
If the replacement and washing instructions are not followed,
the anti-grease fi lters may present a fi re hazard.
• The active carbon fi lters are used to purify the air which is
released back into the room.
The fi lters are not washable or re-usable and must be replaced
at least once every four months.
The active carbon fi lter saturation level depends on the fre-
quency with which the appliance is used, the type of cooking
performed and the regularity with which the anti-grease
fi lters are cleaned.
• Clean the cooker hood frequently, both inside and outside,
using a cloth which has been dampened with denatured
alcohol or neutral, non-abrasive liquid detergents.
• The light on the cooker hood is designed for use during
cooking and not for general room illumination.
Extended use of the light reduces the average duration of
the bulb.
• Commands: (Fig.11)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off .
Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10' , then the appliance go back to work at the
original speed. During this function the display blinks.
Key E = The Timer times the functions on activation for 15
minutes, after which they are switched off . The Timer is deac-
tivated by re-pressing Key E. When the Timer is activated the
decimal point must fl ash on the display. The Timer cannot be
activated if the intensive speed is functioning.
The "clean air" function is activated by pressing key E for 2
seconds when the appliance is switched off . This switches the
motor on for 10 minutes every hour at the fi rst speed. During
functioning a rotary movement of the peripheral segments
must be visualised on the display. When this time has passed
the motor switches off and the fi xed letter "C" must be visu-
alised on the display until the motor re-starts after 50 minutes
for another 10 minutes and so on. Press any key apart from
the light keys to return to normal functioning. Press key E to
deactivate the function.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 15 -
Inhaltsverzeichnis
