Inhaltsverzeichnis
Verfügbare Sprachen
Verfügbare Sprachen
22
Steam cleaning
!
WARNING!
Be particularly careful when cleaning stairs.
CAUTION!
Vacuum your carpets thoroughly prior to steam
cleaning and make sure that your hard floors are
clean and free of grit and debris.
NOTE:
The steam cleaner will turn off if it overheats: Turn
it off and allow it to cool down for at least 2 to 4
hours.
Cleaning hard floors
CAUTION!
The steam poses a risk of slipping. Before enter-
ing the cleaned floors, wait until they are com-
pletely dry.
CAUTION!
Never use the appliance without a microfibre pad
attached to the steam base.
CAUTION!
Not all flooring can withstand the exposure to
steam and moisture. Consult the floor manufac-
turer and have him confirm compatibility. Other-
wise, the flooring could get damaged.
Place the microfibre pad on the floor with white
1
side pointing upwards. Place the floor nozzle on the
microfibre pad and make sure that it covers the en-
tire steam base (fig.
).
11
mains socket.
Place the On/Off button in 'On' po-
3
). ➔ The steam ready indicator is lit.
sition (fig.
/
2
7
The steam cleaner starts heating up. As soon as the
steam ready indicator lights up in green, the steam
cleaner is ready for use.
tomatically set to maximum steam jet without de-
tergent. To change the steam jet, press the program
selector key (fig.
/
) until the corresponding pro-
2
6
gram is lit (fig.
/
–
2
1
4
Low disbursement of steam and detergent;
1
Maximum disbursement of steam and detergent;
2
Insert the plug into a
2
The steam cleaner is au-
4
):
EN
Low steam;
Maximum steam.
3
4
Place foot on the steam base and pull handle
5
backwards (fig.
).
12
duce steam boosts (fig.
moisture on the floor, do not press the steam button
continuously.
Move steam cleaner slowly forwards
7
and backwards across the floor (fig.
need concentrated steam, activate the steam booster
(fig.
1
/
) and press the steam button. The best re-
14
sults are achieved in "Maximum steam + detergent"
mode. To deactivate the steam booster, press the
steam booster (fig.
1
place the On/Off button in 'Off' position
). ➔ The steam cleaner cools down, the
(fig.
/
2
7
steam ready indicator goes out.
of the mains socket.
cooled down, hold corner of microfibre pad down
with your foot and lift steam cleaner to peel away.
Air-dry or wash microfibre pad.
12
Using compact brush
The integrated compact brush can be used to reach
corners and difficult to access areas.
glider with your foot and pull the steam cleaner from
the outer glider (fig.
to access areas, see > "Cleaning hard floors" auf Seite
22.
To reattach the glider, position the glider and
3
press the steam cleaner with compact brush onto the
glider (fig.
).
13
Refreshing carpets
CAUTION!
Never use the appliance without a microfibre
pad attached to the steam base. Use carpet glider
only to refresh carpets.
See > "Cleaning hard floors" auf Seite 22. In addition,
use the carpet glider.
Push steam base with microfibre pad into the
1
front of carpet glider (fig.
part of the steam base into the clip.
steam cleaner has cooled down, press the clip down
with your foot and lift steam cleaner to remove the
carpet glider.
Using steam cleaner without steam base
Activate the release pedal of telescopic tube
1
(fig.
/
) and remove telescopic tube with appli-
1
13
ance body.
Assemble the desired accessory > "Us-
2
ing the accessories" auf Seite 23.
360° adapter, turn the 360° adapter clockwise onto
the telescopic tube until you hear it click in place
(fig.
).
The telescopic tube can be used at dif-
16
4
ferent heights and angles. Clean the desired areas,
see > "Cleaning hard floors" auf Seite 22.
Press the steam button to pro-
6
/
). To prevent excessive
1
10
).
If you
12
8
/
) again.
After cleaning,
14
9
Pull the plug out
10
After the steam cleaner has
11
Fix the outer
1
).
Clean floor on difficult
13
2
14
). Then press the rear
After the
2
When using the
3
Press the
5
Inhaltsverzeichnis
Fehlerbehebung
